Left Hand Telescopic Oven Rail

£55.96
SKU
DG6100468A
Genuine Part
Typically with you in 3 to 8 days
Commonly used on these brands
Genuine Samsung Spare Part

Replacement telescopic oven rail – compatible with Samsung built in oven models as shown unless advised otherwise

Check your oven model number to ensure a guaranteed fit.

 

Description

Bring back the smooth, effortless glide to your Samsung built-in oven with this genuine telescopic rail. As an original Samsung component, it matches the rail fitted at the factory in fit, finish, and load-bearing performance.

The rail extends fully and retracts smoothly, allowing heavy baking trays and roasting tins to be pulled out safely without the risk of tipping. Made from durable stainless steel, it is designed to withstand heat cycles and the daily use of a busy kitchen.

Telescopic rails can fail over time due to wear, physical stress, or accidental damage during cleaning. A rail that no longer slides smoothly, feels gritty or has collapsed under load can make it difficult to remove hot trays safely, increasing the risk of spills and burns. Replacing the rail restores smooth operation and keeps trays stable throughout the cooking cycle. This genuine replacement is manufactured to match the original part's specifications and performance.

This part will only fit the models shown or as specifically advised and will not fit any others, as even if it looks the same, it probably won't be, since several look alike but aren't interchangeable. Please take time to ensure this is correct before ordering. If you are unsure, please don't hesitate to contact us and ask for assistance.

Fits the left hand side only

Technical Notes

Specifications: Genuine Samsung telescopic oven rail (left side). Material: stainless steel. Finish: STS30. Product code: DG61-00468A.

Safety note: No electrical connection is required for this part. Allow the oven to cool completely before handling. Wear gloves when removing the old rail, as edges may be sharp.

Fitment guidance: This rail fits only the Samsung built-in oven models listed in the compatibility matrix below. Model numbers can be found on the rating plate located on the rear panel or on the inner edge of the oven cavity.

 

SAMSUNG BUILT IN OVEN

BQ1D4T081/XSA, BQ1Q4T102/XSA, BQ1Q6T092XEF, BQ1VD6T131, BQ2D7G144XEO, BT62TDBB, BT62TDBSTXEE, NV64R3531BS, NV66M3531BS, NV6783BGESR/EF, NV68A1110BB, NV68A1110RB, NV68A1110RS, NV68A1140BB, NV68A1140BK, NV68A1140BS, NV68A1145CK, NV68A1145RK, NV68A1170BS, NV6986BJUSR/EE, NV70F2793NS/EF, NV70F7584DS/SA, NV70F7786ES/EG, NV70F7796ES/EE, NV70F7796MS, NV70H5587BB/EG, NV70K2340RM, NV70M2341RS, NV70M3571RS/EF, NV75A6549RS, NV75A6579RS, NV75J5170BS, NV75J5540RS/EE, NV75K5541RB, NV75K5541RS, NV75K5571RM/EU, NV75K5571RS/EF, NV75M5572RS/EF, NV75N5641RS, NV75N5671RM, NV75N5671RMEF, NV75N5671RS/EF, NV75N7546RS, NV75N7677RS, NV75R5671RM/EG, NV75R7646RB, NV75R7676RB/EG, NV75R7676RS/EF, NV75T8549RK, NV75T8879RK, NV75T8979RK, NV75T9549CD, NV75T9879CD, NV7B4020ZAK, NV7B4020ZAS, NV7B4040VAK, NV7B4040VAS, NV7B4040VAW, NV7B4045VAK, NV7B41201AK, NV7B41201AS, NV7B41205AK, NV7B41207AK, NV7B41207AS, NV7B4125ZAK, NV7B4125ZAS, NV7B41301AS, NV7B41301ASU1, NV7B41307AK, NV7B41307AS, NV7B41403AK, NV7B41403AS, NV7B4140VAK, NV7B4140VAS, NV7B4145VAK, NV7B4220ZAB, NV7B4225ZAK, NV7B4225ZAS, NV7B4240VAK, NV7B4245VAK, NV7B4245VAS, NV7B4245VAW, NV7B43251AK, NV7B4345VAK, NV7B44205AK, NV7B44205AS, NV7B44207AK, NV7B44207AS, NV7B4420ZAW, NV7B44251AK, NV7B44257AK, NV7B4430ZAB, NV7B4430ZAS, NV7B4440VAK, NV7B4445UAS, NV7B4445VAK, NV7B45251AK, NV7B4525ZAK, NV7B4525ZAS, NV7B45305AS, NV7B4545VAK, NV7B4545VAS, NV7B5645TAS, NV7B5660RAK, NV7B5660XAK, NV7B5685AAK, NV7B5685BAK, NV7B5745PAK, NV7B5745PAS, NV7B5745TAS, NV7B5755SAK, NV7B5755SAS, NV7B5765RAK, NV7B5765XAK, NV7B5785KAK, NV7B6665IAA, NV7B6685AAN, NV7B6685BAK, NV7B6785KAK, NV7B6795JAK, NV7B6799JAK, NV7B7997AAA, NV7B7997AAK, NQ50A6539BK, NQ50J9530BS, NQ50T8539BK, NQ50T8939BK, NQ50T9539BD, NQ50T9939BD, NQ5B4353FBK, NQ5B4353HBK, NQ5B4553FBS, NQ5B4553FBK, NQ5B4553HBK, NQ5B5763DBB, NQ5B5763DBK, NQ5B5763DBS, NQ5B6753CAA, NQ5B6753CAK, NQ5B6753CAN, NQ5B7993AAK

Get Expert Samsung Spare Part Help

Can't find your model number listed or need help identifying the correct part? Contact our parts advisors with your full model and serial number, and we'll verify the correct part for your appliance.

More Information
Further Description

Common Faults & Symptoms

The following symptoms are commonly reported when this part begins to fail. Use this as a diagnostic guide before ordering a replacement — if more than one of these is present, the part is the likely culprit.

1
Rail Does Not Slide Smoothly
The telescopic rail feels gritty, stiff, or requires excessive force to extend and retract. This is often the first sign of wear in the ball-bearing mechanism or a build-up of baked-on grease and debris. A rail that does not glide smoothly makes it difficult to remove hot trays safely and increases the risk of spills.
2
Rail Collapses Under Load
The rail gives way or drops when a heavy tray is placed on it, causing the tray to tilt or fall. This indicates that the internal telescopic mechanism has failed or the mounting bracket has bent. A collapsing rail is a safety hazard, as hot food or liquid can spill when the tray tips.
3
Broken or Bent Mounting Bracket
The bracket that secures the rail to the oven side wall may crack or bend through physical stress or accidental impact. A damaged bracket prevents the rail from sitting level, which can cause trays to sit unevenly and cook inconsistently. Inspect the bracket for hairline cracks or distortion.
4
Tray Does Not Sit Level
When the tray is placed on the rail, it sits at an angle rather than flat. This can be caused by a bent rail, a damaged bracket, or the rail not being correctly seated in the oven side runner. An uneven tray leads to uneven cooking and may cause batter or oil to pool to one side.
5
Rail Detaches from Side Runner
The rail may come loose from its mounting points, either partially or completely. This can happen if the retaining clips are worn or if the rail has been removed and refitted incorrectly during cleaning. A detached rail can fall inside the oven and damage other components.
6
Noise During Operation
A rattling or scraping noise when the rail is extended or retracted indicates internal wear or a loose component. While not always a functional failure, persistent noise is a sign that the rail is deteriorating and may soon fail completely.

Fitment Guidance

This telescopic rail is compatible only with the Samsung built-in oven models listed in the compatibility matrix above. Even if a rail looks visually similar, mounting points and rail lengths can differ between models, so a part that appears to fit may not sit securely.

  • The model number is usually found on a rating plate on the rear panel of the oven or on the inner edge of the oven cavity.
  • For built-in models, pull the appliance forward slightly to access the rating plate if it is on the rear.
  • Compare the full model number, including any suffix after the forward slash, against the list above.
  • Check that the mounting points on your existing rail match the position of the brackets on this replacement.
  • If the model number is not listed, contact our parts advisors before ordering.

Diagnostic Tips

Before concluding that the rail has failed, carry out these checks to rule out other causes. No specialist tools are required for a visual inspection.

  • Visual inspection: Remove the rail and examine it in good light for bent sections, broken welds, or worn ball bearings. Look for grease that has hardened or become gritty.
  • Slide test: Extend and retract the rail by hand. It should move smoothly through its full range without catching, grinding, or excessive play.
  • Load test: Place a moderate weight on the extended rail and check that it does not flex excessively or drop. The rail should support the weight without noticeable deflection.
  • Fit check: Ensure the rail is correctly seated in the side runner. A rail that is not fully clipped into place may feel loose or cause the tray to sit unevenly.
  • Compare with the opposite side: If your oven has a matching rail on the other side, compare the two. Differences in smoothness, noise, or stability can help identify whether one has deteriorated.

Installation Guide

These steps describe the general procedure for replacing a telescopic oven rail. The exact sequence varies between models, so always consult the appliance manual where available.

  1. Allow the oven to cool completely and isolate it from the electrical supply.
  2. Remove all trays, racks, and side runners from the oven cavity to improve access.
  3. If the old rail is still attached, press the retaining clip or unscrew the mounting screws to release it from the side runner. Note how the rail is positioned before removal.
  4. Clean the side runner and the mounting area to remove any built-up grease or debris.
  5. Position the new rail on the side runner, aligning the mounting points with the corresponding holes or clips.
  6. Secure the rail in place, ensuring it is fully seated and does not wobble. If screws are used, tighten them evenly.
  7. Extend and retract the rail by hand to confirm smooth operation through its full range.
  8. Replace the side runner, trays, and racks, then restore the electrical supply and test the oven through a heating cycle.

Before Ordering, Check These First

  • Verify your full model number against the compatibility list above, including any suffix after the forward slash.
  • Confirm you are ordering the correct side — this part is the right-hand telescopic rail.
  • Check that the mounting points on your existing rail match the position of those on this replacement.
  • Inspect the side runner for damage before ordering, as a damaged runner may also need attention.
  • Rule out incorrect seating or hardened grease as the cause of stiffness before replacing the rail.
  • Contact our parts advisors if any doubt remains about fitment before placing your order.

Disclaimer: The fault codes and symptoms listed above are intended as a general guide to assist with diagnosis. They cannot be taken as a definitive diagnosis of any particular problem, and other components may produce similar symptoms. Always confirm the fault with proper testing before ordering parts.

Alternate Part Number DG61-00468A, SAMDG61-00468A, 5045382704301
Manufacturer SAM
Genuine Part Yes

Oven & Cooker Spares 

Oven
Shelves & Trays

Oven shelves and trays may be original or universal replacements. While original parts are model-specific, universal alternatives often provide excellent function at a much lower price.

Ordering Oven Shelves & Trays

Oven trays and shelves can be costly if purchased as genuine spares. We offer universal alternatives that are often just as good but more affordable. Original fit shelves are only recommended if you require the exact manufacturer specification.

Special trays with stops or shaped areas may require the original part to function correctly. Always confirm your model and size before ordering.

Can't Find The Oven Shelf or Tray You Need?

Oven shelves and trays may look similar, but a few millimetres or a specific stop can make all the difference. Provide your oven or cooker details and we’ll help you find the correct replacement part quickly and efficiently.

Contact Support Team
Samsung Global Electronics & White Goods Giant

Samsung
Spare Parts.

Samsung is a global powerhouse, transitioning from dominance in consumer electronics to becoming one of the world's largest appliance brands. From their legendary American Fridge Freezers to built-in ovens and laundry, their technical ecosystem is vast and complex.

The Data "Information Gap"

Samsung's spare parts supply can be unpredictable. Official technical data is often sparse, and pricing for certain components can be highly volatile. We use our specialist networks to bridge this gap and provide accurate fitment.

Full Model Code
Version ID
Serial Verification
Guaranteed Fit
 

Check Suitability First

Samsung parts undergo frequent design revisions mid-production. A part that looks identical may have a different internal protocol or connector. Always check suitability with our team if you aren't 100% certain.

 

Professional Verification

Because Samsung's own information can be poor, we manually verify requests against known successful repairs. We'd rather take the time to be correct than send a part that doesn't fit your specific revision.

Request Samsung Technical Support

Don't overpay for the wrong part. Send us your full model code and serial number, and let our specialists identify the most cost-effective genuine spare for your machine.

Contact Specialist Team

Samsung Technical Network • Revision Verification • Established 1988

NWAR SUPPORT

Spare Parts Help

Identifying technical spares can be a minefield. Our specialist help desk is available via email to cross-reference your model and identify the most cost-effective genuine or alternative options.

Avg. Response Under 60 Minutes
Service Type Expert Verification
Ask A Specialist

Or use the live chat widget below.

UK'S Professional Appliance Spare Part Network • Established 1988

Logistics & Support

Delivery & Returns Information.

We aim to get your parts to you as fast as possible. We are transparent about lead times, stock availability, and our returns process to ensure a smooth repair.

Stock Availability

Please be aware that we show availability but do not display live stock levels online. Estimates are based on average manufacturer lead times.

Tradesman Warning

Do not arrange a tradesman until your goods have arrived and been checked. We do not cover tradesman costs due to transit delays or suitability issues.

Understanding Lead Times

1 to ** Days

Normally a UK stock item. Dispatched same or next working day. Some items may take longer depending on specific warehouse location.

3 to ** Days

Usually a UK/EU stocked item but with a longer lead time. Contact us before ordering for specific clarification if the repair is urgent.

* to ** Days

Factory or Custom order items. These are ordered specifically for you and cannot ordinarily be returned. Please allow the full time indicated.

Order Transit

Orders placed before 3:00 PM (Mon-Fri) for in-stock items are typically dispatched same-day.

We use Royal Mail, DPD, and Evri. Tracking information is emailed upon dispatch. Delivery times to rural or offshore areas will vary.

Heavy/Oversized Items

Items such as dishracks, tubs, and glass cooktops may incur additional fees due to weight and specialised packaging requirements. We will contact you if additional shipping is required.

Returns Policy

Damages

Report transit damage within 24 hours. Include a photo of the damage and the packaging to speed up the claim process.

Cancellations

You have 14 days after delivery to cancel. This must be done via email or support ticket (not phone/chat).

Exclusions

We cannot accept returns for items that have been fitted for fault-finding, used, or custom-ordered.

How to Return an Item

1

Contact us with your order number and reason for return.

2

Wait for instructions and the correct returns address (this varies by item).

3

Package carefully. Do not deface original packaging. Use tracked post.

Have questions about your delivery or a potential return?

Contact Support Team

98% of orders delivered on time • Expert Resolution • Established 1988

 

Need Assistance?

Our advisors can help you identify spares faster, query prices, find alternatives and save you time and money.

 
 
Fast Free Advice Mon-Fri, 9am - 5pm
 Contact Our Parts Specialists
© NWAR. All rights reserved. Manufacturer logos, images and documentation for informational purposes only.