Extraction Hob Carbon Filter
Replacement carbon filter for extraction hobs – compatible with AEG and Electrolux models as shown unless advised otherwise
Description
This genuine carbon filter is identical to the original supplied with the extraction hob, restoring the odour-removal stage that keeps cooking smells out of the kitchen when the appliance is used in recirculation mode.
Helsa manufactures it to the original specification, using activated carbon held in a plastic frame that slots directly into the filter housing beneath the hob surface. The carbon traps odour molecules as they pass through, while the surrounding grease filter captures fat and smoke particles; together, they form a complete filtration system.
Unlike disposable carbon filters, this one is regenerable. You can regenerate it by heating it in an oven preheated to 200°C for about 45 to 60 minutes, which drives off trapped odours and restores performance. With regular regeneration, the filter can last up to five years, making it a genuinely long-term component rather than a consumable. Even so, it will eventually become permanently saturated and need replacing, and a saturated filter is one of the most common reasons for persistent cooking odours and reduced extraction performance.
The pack of four shown in related items is a cheaper way to buy these filters.
This part will only fit the models as shown or as specifically advised and will not fit any others even if it looks the same, it probably won't be as there are several that look alike yet are not. If you are unsure please don't hesitate to contact us and ask for assistance.
Technical Notes
Specifications: Genuine Electrolux carbon filter for extraction hobs; activated carbon in plastic frame; Helsa cube type; dimensions 104 mm x 104 mm x 50 mm; approximate weight 346 g; supplied as 1 unit; product code 4055380481. Alternate part number: 4055405015.
Note: This filter is regenerable, not disposable. You can thermally regenerate it every 2–3 months in an oven preheated to 200°C for 45–60 minutes; with regular regeneration, it has a maximum lifespan of up to 5 years. Replace a filter that has exceeded this lifespan, or that no longer responds to regeneration.
Safety note: The filter itself has no electrical connections, but the surrounding hob components do. Isolate the hob from the power supply before removing or refitting the filter, and allow the appliance to cool completely. Handle the filter by its frame and avoid damaging the carbon block, as loose carbon dust can be messy and difficult to clear from the appliance.
⚠️ Warning: Customer ordered upon request only. This is a non-returnable item that cannot be cancelled once ordered.
AEG BUILT IN EXTRACTION HOB
IDE84241IB (942150598), IDE84241IB (942150638), IDK84451IB (942150516), IDK84451IB (942150636)
ELECTROLUX BUILT IN EXTRACTION HOB
DMGL8320SW (942150678), DMGL8360SW (942150627), DMGL8370SW (942150626), DMGL8370SW (942150676)
Get Expert Electrolux Spare Part Help
Can't find your model number listed or need help identifying the correct part? Contact our parts advisors with your full model and serial number, and we'll verify the correct part for your appliance.
| Further Description |
Common Faults & SymptomsThe following symptoms and fault indicators are commonly reported when the carbon filter in an extraction hob becomes saturated or reaches the end of its life. Use this as a diagnostic guide before ordering a replacement — if more than one of these is present, the filter is the likely culprit. 1
Persistent cooking odours in the kitchen
The most obvious sign. Smells that the extraction hob used to clear now linger in the air after cooking, because the saturated carbon can no longer adsorb odour molecules.
2
Filter saturation indicator illuminated
The hob displays a filter icon or LED to show that the carbon filter needs attention. On many models this indicator counts operating hours rather than measuring odour directly, so it will light up even if the filter does not yet smell.
3
Indicator stays on after resetting
If the saturation indicator remains lit or blinks after following the reset procedure, the filter may need to be regenerated or replaced, or the reset procedure may need to be repeated.
4
Reduced extraction airflow
Even on the highest fan setting, the extraction feels weaker than it used to. A clogged carbon filter restricts airflow, which also puts extra strain on the fan motor.
5
Greasy film on kitchen surfaces
A sticky residue builds up on walls, cabinets and worktops near the hob. When the carbon filter is saturated, grease-laden air can bypass effective filtration and settle on surfaces.
6
Unpleasant stale smell from the hob
The hob may start to emit an odour of its own, particularly when first switched on. Trapped grease and organic matter held in a saturated filter can turn stale and become a source of smell rather than a cure for it.
7
Condensation on windows and walls
Moisture from cooking condenses more heavily than before because the hob is moving less air. Poor extraction in recirculation mode is often traced back to a clogged carbon filter.
8
Filter has exceeded its regeneration lifespan
If the filter has been regenerated regularly for close to five years, or if it no longer responds to regeneration, it has reached the end of its life and should be replaced regardless of how it looks.
Fitment GuidanceThis carbon filter is compatible only with the AEG and Electrolux models listed in the compatibility matrix above. Even if a filter looks visually similar, the dimensions, frame profile and airflow characteristics can differ between extraction hob ranges.
Diagnostic TipsBefore concluding that the carbon filter needs replacing, carry out these checks to rule out other causes.
Installation GuideThese steps describe the general procedure. The exact sequence varies between models, so always consult the appliance service manual where available.
Before Ordering, Check These First
Disclaimer: The fault codes and symptoms listed above are intended as a general guide to assist with diagnosis. They cannot be taken as a definitive diagnosis of any particular problem, and other components may produce similar symptoms. Always confirm the fault with proper testing before ordering parts. |
|---|---|
| Alternate Part Number | FCB0132356B, FCB0143192A, KIT0120952A, 4055405015, DST4055380481 |
| EAN Number | 7321423869658 |
| Manufacturer | Genuine Lux1AE |
| Genuine Part | Yes |
Cooker Hood Filter Specialist
Cooker Hood
Filters
Cooker hood filters come in two main types: grease filters, which prevent grease entering the motor, and carbon/charcoal filters, which remove odours and protect the motor. All hoods require a grease filter, and non-vented hoods should also have a carbon filter fitted. Regular replacement or cleaning is essential for optimal performance.
Filter Replacement Guidelines
- Grease filters: replace every 1–6 months depending on cooking frequency and type
- Carbon/charcoal filters: replace every 3–6 months for optimal odour removal
- Metal mesh grease filters: clean regularly to prevent blockage or damage
- Replacement frequency depends on cooking habits rather than just manufacturer guidelines
Some cooker hood filters are highly model-specific. Images and sizes are for illustration only. Always check compatibility with your specific model to ensure correct fit and performance.
Important: Do not rely solely on images, as filters can appear identical but be incompatible. Always refer to model specifications and contact us if unsure.
Can't Find The Cooker Hood Filter You Need?
Finding the right cooker hood filter can be tricky due to model numbers, serial numbers, and specific filter types. We aim to make it simple, but sometimes a little expert help is needed.
Contact us using our page or email, so we can check compatibility, identify low-cost alternatives, and ensure you receive the correct filter quickly, saving you time, hassle, and money.
AEG Brand - Electrolux Group
AEG
Spare Parts.
AEG is a German brand within the Electrolux Group. Older German-made appliances were well-regarded, though more recent models vary in quality. Correct identification of spare parts is essential due to multiple variants per appliance.
Model & PNC Verification
To accurately locate AEG spare parts, you will usually need the Product or PNC number from the appliance rating plate. This ensures compatibility across multiple variants, which may range from a few to over thirty per model.
Ordering & Assistance
Some AEG parts are straightforward to order, while others require careful verification. If unsure, please contact us to get guidance on correct parts and possible lower-cost alternatives.
Group Compatibility
AEG spare parts are used across multiple Electrolux Group brands. Thankfully, all products function similarly, making cross-brand identification easier.
Confirm Your AEG Spare Parts
Provide the Product or PNC number from your appliance’s rating plate and our team will confirm the correct AEG spare parts for your model quickly and accurately.
Contact Support TeamGerman Brand • Verified Fitment • Electrolux Group • Established 1988
UK'S Professional Appliance Spare Part Network • Established 1988
Delivery & Returns Information.
We aim to get your parts to you as fast as possible. We are transparent about lead times, stock availability, and our returns process to ensure a smooth repair.
Stock Availability
Please be aware that we show availability but do not display live stock levels online. Estimates are based on average manufacturer lead times.
Tradesman Warning
Do not arrange a tradesman until your goods have arrived and been checked. We do not cover tradesman costs due to transit delays or suitability issues.
Understanding Lead Times
Normally a UK stock item. Dispatched same or next working day. Some items may take longer depending on specific warehouse location.
Usually a UK/EU stocked item but with a longer lead time. Contact us before ordering for specific clarification if the repair is urgent.
Factory or Custom order items. These are ordered specifically for you and cannot ordinarily be returned. Please allow the full time indicated.
Order Transit
Orders placed before 3:00 PM (Mon-Fri) for in-stock items are typically dispatched same-day.
We use Royal Mail, DPD, and Evri. Tracking information is emailed upon dispatch. Delivery times to rural or offshore areas will vary.
Heavy/Oversized Items
Items such as dishracks, tubs, and glass cooktops may incur additional fees due to weight and specialised packaging requirements. We will contact you if additional shipping is required.
Returns Policy
Damages
Report transit damage within 24 hours. Include a photo of the damage and the packaging to speed up the claim process.
Cancellations
You have 14 days after delivery to cancel. This must be done via email or support ticket (not phone/chat).
Exclusions
We cannot accept returns for items that have been fitted for fault-finding, used, or custom-ordered.
How to Return an Item
Contact us with your order number and reason for return.
Wait for instructions and the correct returns address (this varies by item).
Package carefully. Do not deface original packaging. Use tracked post.
Have questions about your delivery or a potential return?
Contact Support Team98% of orders delivered on time • Expert Resolution • Established 1988
